Van Load Fit Calculator

Enter the size of a sofa, fridge, wardrobe or box and compare it with a van's load space and rear door opening. The calculator tests every way the item could be turned and tells you which one fits, how many would go in and whether the weight is within payload.

Will it fit in the van?

Start with the item, then choose an example van or enter your own.

✦ Free · no sign-up
01

Your item dimensions

Measure the widest points, including packaging, legs and handles.

cm
cm
cm
kg
pcs
cm
02

Choose a van

Example vans are illustrative. For a real check, choose "My van" and enter measured sizes.

Illustrative medium van (SWB): 240 × 160 × 140 cm load space; rear opening 140 × 125 cm; 900 kg example payload. Not a manufacturer specification.

Internal load space

cm
cm
cm

Rear door opening and payload

cm
cm
kg

Your fit result

Example van
REAR DOORSCABTOP VIEW · TO SCALE · 1 ON THE FLOOR
Load floor seen from above
REAR VIEW · DOOR OPENING
Item end-on in the door
Possible fit found

At least one orientation clears the rear door opening and the load space with your 5 cm safety gap. Check the real loading conditions below before you rely on it.

Item volume (total)
1.148 m³ (40.5 ft³)
Item weight (total)
42 kg 5% of payload
Load space
240 × 160 × 140 cm (5.38 m³)
Rear door opening
140 × 125 cm
Best orientation (L × W × H)
180 × 75 × 85 cm
Orientations that fit
2 of 6
How many fit (estimate)
2 (1 long × 2 across, not stacked)
Share of load space used
21%
  • Van figures are an illustrative medium van (SWB). Choose "My van" and enter the measured sizes for a real check.

How to use the van load fit calculator

Pick your units first. Centimetres are the default, but you can switch to millimetres, metres, inches or feet and the numbers already typed will convert for you. Then enter the item's length, width and height, its weight and how many you have.

  1. Measure the item at its widest points. Include feet, handles, rolled arms and any packaging. A sofa measured "arm to arm" but not over the back cushions is a common source of bad results.
  2. Set a safety gap. This is extra room you want on every measurement, for fingers, moving blankets and straps. Five centimetres is a sensible minimum for furniture.
  3. Choose a van. The small, medium, large and Luton options are illustrative examples so you can get a feel for sizes. For a real decision, pick "My van" and type in the load length, width, height, door opening and payload from the hire company's specification sheet or your own tape measure.
  4. Read the result and the notes. The badge gives the verdict, and the drawings show the item on the load floor and end-on in the door opening.

How the calculation works

A box has six possible orientations: any of its three measurements can point into the van, and the other two can be swapped. The calculator tries all six. For each one it runs two checks.

The first is the load space check. The measurement pointing into the van, plus the gap, must be no more than the load length. The other two must clear the load width and height.

The second is the door check, and it is the one people forget. As the item slides in through the back, its cross-section (width and height in that orientation) has to pass through the rear door opening. On most panel vans the opening is noticeably smaller than the space behind it, so an item can fit inside the van and still be impossible to load.

fits = (length + gap ≤ load length) and (width + gap ≤ load width and door width) and (height + gap ≤ load height and door height)

When several orientations pass, the calculator picks the one that lets the most items in, and then the one with the lowest standing height, because low and flat is usually more stable. The "how many fit" figure is a simple grid count: how many copies line up along the length and across the width, and how many stack if you tick the stacking box. It does not mix orientations, so a careful loader can sometimes beat it with boxes. Finally, the total weight is compared with the payload you entered.

Worked example: a three-seater sofa in a medium van

Say the sofa measures 200 cm long, 90 cm deep and 85 cm high and weighs 55 kg. The example medium van has a load space of 240 × 160 × 140 cm and a rear opening of 140 × 125 cm. With a 5 cm gap:

CheckNeeded (with gap)AvailableResult
Length into the van205 cm240 cmPasses
Width across the van95 cm160 cmPasses
Height90 cm140 cmPasses
Door width and height95 × 90 cm140 × 125 cmPasses
Weight55 kg900 kgPasses

The sofa goes in lengthways, sitting on its feet. Change the example van to "Small van" and the same sofa fails, because no orientation brings the 200 cm length under the 170 cm load floor. That is exactly the kind of mistake that costs a second hire.

What this tool cannot tell you

It cannot see your van. Real load spaces are not perfect boxes. Wheel arches eat into the floor width, often by 30 cm or more between them, and side walls taper towards the roof. Some vans have a bulkhead that slopes, and many have lashing rails or ply lining that take a centimetre or two off each side.

It also assumes the item goes straight in. Sofas can often be tipped and angled through an opening that looks too small, and a tall fridge freezer can go in upright through a high-roof door but not a low one. If the result is "fits inside, but not through the doors", it is worth checking the side loading door and the diagonal measurements before giving up. Our guide to van loading door dimensions explains how.

And it does not judge safety. A load that fits still has to be secured so it cannot slide or topple, and the van must stay inside its maximum authorised mass and axle limits. Use the van payload calculator for the weight side.

Tips for accurate measurements

  • Use a steel tape, held straight. Fabric tapes stretch and curve around cushions.
  • Measure twice and round up to the next centimetre, never down.
  • Remove what you can. Feet, sofa arms on some models, table legs and wardrobe doors often unscrew, and a few centimetres can change the verdict.
  • Measure the van too. Hire companies usually publish load length, width between arches and door sizes. If they do not, ask, or take a tape when you collect.

For a fuller walk-through, read how to measure furniture for a van.

Frequently asked questions

Does a "possible fit" mean the item will definitely go in?

No. It means the simple box measurements and the rear door opening allow it under the assumptions above. Treat it as a strong hint and check the real van, especially wheel arches and the door shape.

Why does my item fit inside but fail at the doors?

Rear door openings are usually smaller than the load space, because the door frame, hinges and roof structure sit inside the van's outer shape. The cross-section of the item has to pass through that smaller hole.

Which units can I use?

Centimetres, millimetres, metres, inches or feet for sizes, and kilograms or pounds for weight. Changing the unit converts the numbers already entered.

What safety gap should I use?

Around 5 cm for furniture and appliances, so there is room for hands and protective blankets. For tightly packed boxes, 1 to 2 cm is enough.

Can I share or print the result?

Yes. After you calculate, the page address includes your inputs, so you can copy it. The "Print or save as PDF" button prints just the result.